Sensaphone

The XFR-0041 and XFR-0046  is a 5 V .3 amp transformer required when using the WSG30 wireless sensors as a router. This is required because router mode uses more power than can be supplied by batteries alone for an extended period of time. You can also use this power supply when the sensor is configured as an End Point, which will greatly extend the life of the batteries and minimize the need to change them.

The XFR-0041 and XFR-0046  is a 5 V .3 amp transformer required when using the WSG30 wireless sensors as a router. This is required because router mode uses more power than can be supplied by batteries alone for an extended period of time. You can also use this power supply when the sensor is configured as an End Point, which will greatly extend the life of the batteries and minimize the need to change them.

For use with all Sensaphone models* except 400 and 800. A space mount, low profile humidity transducer. Transmits actual humidity levels to the Sensaphone for programmable high and low alarm limits. The device can be used with any Sensaphone that supports 4-20mA inputs.

Exclusively for use with the FGD-0052 Humidity Transmitter, the FGD-0065 Carbon Monoxide Sensor, the FGD-0066 Air Quality Sensor, and the FGD-0068 Carbon Dioxide Sensor. It is only required when connecting the transmitter/sensors to the Sensaphone 2000. (Other compatible models supply their own 24V power.

Old Code: M-001-0076, New Code: PS110 A compact power outage monitoring device to protect against power outages. The Power-Out Alert easily plugs into any 110 VAC receptacle outlet for operation.Works with all Sensaphone products.  Output is Normally Open. Includes 15 ft. cable.  Note:  This unit has an activation delay of approximately 3.

Sensaphone FGD-0057 external microphone attachment for use with Sensaphone 1400, Sensaphone 1800, or Sensaphone Station Sitter. (Also compatible with Sensaphone Express II; however, that system comes with an external microphone already.

Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. the 1" x .5" LCD displays the PPM and menu parameters. The sensor will require a 24VDC power supply to operate (Part # FGD-0053).

The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053).

The Sensaphone FGD-0220 J-Type Thermocouple/4-20mA Converter will allow you to use a standard J-type thermocouple on any Sensaphone that accepts a 4-20mA input signal. Thermocouple not included. This thermocouple to 4-20mA converter is useful when monitoring very high or very low temperatures that cannot be monitored with a standard Sensaphone temperature sensor.

Sensaphone FGD-0221 USB to RS-232 Converter for use with Sensaphone 2000, Sensaphone SCADA 3000, Sensaphone Skymetry, and Sensaphone IMS models. .

The WSG Wireless Temperature sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and temperature element for monitoring temperature wherever the device is installed. You can remove the internal temperature element and attach a remote temperature probe so that measurements can be made in a refrigerator, freezer or other harsh environment.

The WSG Wireless Temperature sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and temperature element for monitoring temperature wherever the device is installed. You can remove the internal temperature element and attach a remote temperature probe so that measurements can be made in a refrigerator, freezer or other harsh environment.

The WSG30 Wireless Spot Water Detection Sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and water sensing probes for monitoring for the presence of water at a particular location. The sensor comes with three AA alkaline batteries which will power the sensor for up to two years.

The WSG Wireless Power Failure sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter, two AA alkaline batteries and a wall plug in power supply. The sensor will detect a loss of power at the outlet where the power supply is attached. The two AA alkaline batteries will power the sensor and allow it to transmit alarm information in the event that 120VAC power fails.

The WSG Wireless Dry Contact sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and input terminals for connecting to any normally-open or normally closed output. (Use of this device with solid-state outputs is not recommended) The sensor comes with two AA alkaline batteries which will power the sensor for up to two years.

The WSG30 Wireless 4-20mA sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter, 4-20mA input and a 24V loop power supply. The sensor can be used to monitor the output of any 4-20mA transducer. The sensor comes with a plug-in power supply and three AA alkaline batteries which will power the sensor for several hours if main AC power fails.

The WSG30 Wireless Zone Water Detection Sensor is designed to work with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and ten feet of water sensing cable for monitoring for the presence of water in a particular area. The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope.

The WSG Wireless Humidity Sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and humidity sensor element for monitoring humidity wherever the device is installed. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years.

The Sensaphone IMS-4310 Dual Relay Output Module allows you to control two devices from any IMS-4000 Host or Node. Each output may be controlled either manually or automatically. Each output has the option of providing either a dry relay contact or 12VDC power. Two switches located inside the device select the output type.

The IMS-4815 Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm such as defrost cycles, opening of doors and fans circulating air.