Sensaphone

The Sensaphone Pressure Sensor can be used to measure and detect loss of pressure in many applications. An alarm from the pressure sensor can indicate a problem with a pump, a possible clogged influent line, loss of suction, a downstream clog or perhaps a burst pipe. Any of those failures can cause a pump motor to overheat and warp.

SELF-POWERED infrared sensor that monitors the movement of warm bodies in a specific area. Will cause a dialout if motion is detected. The range is a maximum of 40 feet directly ahead of, and approximately 20 feet to either side of, the detector at 40 feet distance (see installation instructions for diagram).

The Humidistat Humidity Switch can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic, a nylon sensing element provides long life and accurate humidity control.

The Zone Water Detector senses the presence of water via the attached WaterRope. The Zone Water Detector can be used with all models of Sensaphone. The sensor is a normally closed device. It operates on two (2) AA batteries (installed). The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope.

10 foot length of WaterRope for the FGD-0056 Zone Water Detector. Up to ten (10) lengths of 10 foot rope (total length 100 feet) can be cascaded from a single Zone Water Detector. Dimensions: 10 feet long Compatible with the FGD-0056 Zone Water Detector.

For use with all Sensaphone models* except 400 and 800. A space mount, low profile humidity transducer. Transmits actual humidity levels to the Sensaphone for programmable high and low alarm limits. The device can be used with any Sensaphone that supports 4-20mA inputs.

Old Code: M-001-0076, New Code: PS110 A compact power outage monitoring device to protect against power outages. The Power-Out Alert easily plugs into any 110 VAC receptacle outlet for operation.Works with all Sensaphone products.  Output is Normally Open. Includes 15 ft. cable.  Note:  This unit has an activation delay of approximately 3.

The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053).

The IMS-4815 Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm such as defrost cycles, opening of doors and fans circulating air.

The IMS-4815 Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm such as defrost cycles, opening of doors and fans circulating air.

The Sensaphone IMS-4863 Airflow sensor is designed to monitor for the presence or absence of cool moving air. This is especially useful for monitoring air conditioning systems. The sensor can provide relative air flow as a percentage from 0 to 100. The sensor is compatible with both the Sensaphone IMS-1000 and Sensaphone IMS-4000 devices.

The IMS-4816 Temperature Sensor with External Probe is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor temperatures in areas where a traditional sensor won’t fit. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable.

Sensaphone IMS-4810 Room Temperature Sensor for Sensaphone IMS-4000 or Sensaphone IMS-1000 The Sensaphone IMS-4810 temperature sensor is designed to connect to the Sensaphone IMS series product line and monitor indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included).

Sensaphone IMS-4812 Mini-Temperature Sensor w/7' Cable for Sensaphone IMS-4000 or Sensaphone IMS-1000 The IMS-4812 Mini Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor temperatures in tight locations (for example, inside equipment racks).

Sensaphone IMS-4813 Room Temperature Sensor with Display (oC) for Sensaphone IMS-4000 or Sensaphone IMS-1000. The Sensaphone IMS-4813 temperature sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor indoor temperatures.

Sensaphone IMS-4820 Room Humidity Sensor for Sensaphone IMS-4000 or Sensaphone IMS-1000 The Sensaphone IMS-4820 humidity sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor indoor humidity levels. The electrical connection between the sensor and IMS is made via RJ-45 patch cable (not included).

Sensaphone IMS-4821 Room Humidity Sensor with Display for Sensaphone IMS-4000 or Sensaphone IMS-1000 The IMS-4821 humidity sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor indoor humidity. The electrical connection between the sensor and IMS is made via RJ-45 patch cable (not included).

Sensaphone IMS-4830 Water/Flood Sensor with 10' Rope for Sensaphone IMS-4000 or Sensaphone IMS-1000 The IMS-4830 Water Detection Sensor protects your server and equipment from damaging water leaks from malfunctioning HVAC systems, cafeteria accidents, or any general plumbing failures in your facilities.

Sensaphone IMS-4831 Additional 10' Water Detection Rope for Sensaphone IMS-4830 Water Sensor This is a special order item.

Sensaphone IMS-4840 External Power Sensor for Sensaphone IMS-4000 or Sensaphone IMS-1000 The Sensaphone IMS-4840 External Power Sensor lets you monitor power anywhere within your infrastructure. It reports any loss of power and measures the current voltage in the circuit, allowing you to know the status of each server rack and even of your remote UPS.