Flood/Water

The Zone Water Detector senses the presence of water via the attached WaterRope. The Zone Water Detector can be used with all models of Sensaphone. The sensor is a normally closed device. It operates on two (2) AA batteries (installed). The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope.

10 foot length of WaterRope for the FGD-0056 Zone Water Detector. Up to ten (10) lengths of 10 foot rope (total length 100 feet) can be cascaded from a single Zone Water Detector. Dimensions: 10 feet long Compatible with the FGD-0056 Zone Water Detector.

Sensaphone IMS-4830 Water/Flood Sensor with 10' Rope for Sensaphone IMS-4000 or Sensaphone IMS-1000 The IMS-4830 Water Detection Sensor protects your server and equipment from damaging water leaks from malfunctioning HVAC systems, cafeteria accidents, or any general plumbing failures in your facilities.

Sensaphone IMS-4831 Additional 10' Water Detection Rope for Sensaphone IMS-4830 Water Sensor This is a special order item.

A reliable float for water tank, water level and sump pit applications. Reliable monitoring using reed switch technology. The PumpAlarm Cellular Alarm will send text message notifications when water levels are able to lift the float.  Prevent damage associated with water levels in your basement or light commercial application.

The Detectit Hardwired Wastewater Backup Alarm comes with a sensor that screws right into the main house trap and is equipped with a diaphragm that when pushed up by backing up waste water it will trigger your alarm system. The DETECTIT can be connected to an alarm panel or autodialer so you can get alerts from your home, investment property, cottage, or office when your not there.

Monitor two zones with one on-board temperature sensor and an additional remote temperature, humidity or water sensing probe. If temperatures and/or humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor, the designate relay for each zone will activate an alarm, dialer, siren, etc.

Monitor two zones with one on-board temperature sensor and an additional remote temperature, humidity or water sensing probe. If temperatures and/or humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor, the designate relay for each zone will activate an alarm, dialer, siren, etc.

Monitor four zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug sensor the designated relay for eachzone will activate an alarm, dialer, siren, etc.

Monitor four zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug sensor the designated relay for eachzone will activate an alarm, dialer, siren, etc.

The model WB-200 operates on 12 or 24 Volt AC/DC and has a form C relay output that can be connected to alarm panels, bells, dialers, etc. The unit can monitor up to as many as six sensor probes wired in parallel, up to 100 feet away using 22-18 AWG twisted pair. Each sensor probe has two contacts.

Old Code: 1047, New Code: WB350 Use with your Sensaphone for invaluable protection against costly water damage!  The model WB-350 operates on a 9-volt transistor battery (Not included) has an open collector output that can be connected to alarm panels, bells, dialers, etc.

The supervised under carpet water sensor can be connected to the EnviroAlert products as well as the WB-800. The alarm will be activated if water is present as well as if the cable is cut. Supervised under carpet water sensor for the WaterBug 800, EnviroAlert 200, EnviroAlert 400, and EnviroAlert EA800-ip.

Supervised surface water sensor for use with the WaterBug 8 zone water detection monitor (WB-800) or the EnviroAlert (EA200, EA400, OR EA800-ip). Stable surface mount design. Supervised probes will alarm if wire is severed as well as when water is detected. Maximum recommended cable run [22 AWG twisted pair] 500’ (152.