Sensaphone

The Sensaphone Pressure Sensor can be used to measure and detect loss of pressure in many applications. An alarm from the pressure sensor can indicate a problem with a pump, a possible clogged influent line, loss of suction, a downstream clog or perhaps a burst pipe. Any of those failures can cause a pump motor to overheat and warp.

SELF-POWERED infrared sensor that monitors the movement of warm bodies in a specific area. Will cause a dialout if motion is detected. The range is a maximum of 40 feet directly ahead of, and approximately 20 feet to either side of, the detector at 40 feet distance (see installation instructions for diagram).

The Humidistat Humidity Switch can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic, a nylon sensing element provides long life and accurate humidity control.

The Zone Water Detector senses the presence of water via the attached WaterRope. The Zone Water Detector can be used with all models of Sensaphone. The sensor is a normally closed device. It operates on two (2) AA batteries (installed). The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope.

10 foot length of WaterRope for the FGD-0056 Zone Water Detector. Up to ten (10) lengths of 10 foot rope (total length 100 feet) can be cascaded from a single Zone Water Detector. Dimensions: 10 feet long Compatible with the FGD-0056 Zone Water Detector.

The Sensaphone FGD-0102 10K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits.

The Sensaphone FGD-0103 10K indoor decorator zone temperature sensor offers precision room temperature sensing in an attractive wall–mounted enclosure. Accurate to 0.36 F (0.2 C) with a sensing range of 35 to 140 F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate.

The Sensaphone FGD-0105 10K Immersion temperature sensor is a waterproof temperature sensor for measuring the temperature of fluids inside a pipe. It's constructed of brass WEL-B thermowell (which screws into a customer-supplied 0.5" NPT saddle or Thredolet fitting in a pipe). It fits into a thermowell via a brass 0.

For use with all Sensaphone models* except 400 and 800. A space mount, low profile humidity transducer. Transmits actual humidity levels to the Sensaphone for programmable high and low alarm limits. The device can be used with any Sensaphone that supports 4-20mA inputs.

Old Code: M-001-0076, New Code: PS110 A compact power outage monitoring device to protect against power outages. The Power-Out Alert easily plugs into any 110 VAC receptacle outlet for operation.Works with all Sensaphone products.  Output is Normally Open. Includes 15 ft. cable.  Note:  This unit has an activation delay of approximately 3.

Sensaphone FGD-0057 external microphone attachment for use with Sensaphone 1400, Sensaphone 1800, or Sensaphone Station Sitter. (Also compatible with Sensaphone Express II; however, that system comes with an external microphone already.

Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. the 1" x .5" LCD displays the PPM and menu parameters. The sensor will require a 24VDC power supply to operate (Part # FGD-0053).

The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053).

The Sensaphone FGD-0220 J-Type Thermocouple/4-20mA Converter will allow you to use a standard J-type thermocouple on any Sensaphone that accepts a 4-20mA input signal. Thermocouple not included. This thermocouple to 4-20mA converter is useful when monitoring very high or very low temperatures that cannot be monitored with a standard Sensaphone temperature sensor.

Detects any unauthorized entry or intrusion. Usually installed on doors and windows, the sensors monitor their opening and closing. Several magnetic reed switches may be wired in series. Dimensions: 2.5" x 0.75" x 0.5" (part with screw terminals); 2.5" x 0.75" x 0.625" (part with magnet) Compatible with Sensaphone, hardwired security systems, and the WisDom Wireless Universal Transmitter.