Sensaphone

The Sensaphone Pressure Sensor can be used to measure and detect loss of pressure in many applications. An alarm from the pressure sensor can indicate a problem with a pump, a possible clogged influent line, loss of suction, a downstream clog or perhaps a burst pipe. Any of those failures can cause a pump motor to overheat and warp.

The Ethernet to WiFi Adapter is a high-speed, long-range outdoor wireless bridge that is an ideal solution for adding Wi-Fi connectivity to any network based Sensaphone. This is a cost effective solution when faced with running communication cable or trenching long runs of alarm wire to the Sensaphone.

SELF-POWERED infrared sensor that monitors the movement of warm bodies in a specific area. Will cause a dialout if motion is detected. The range is a maximum of 40 feet directly ahead of, and approximately 20 feet to either side of, the detector at 40 feet distance (see installation instructions for diagram).

Detects the presence of water on a horizontal surface. INDEPENDENTLY POWERED* by internal lithium batteries. Multiple sensors can be wired in series to a single input. Comes with 10' of hookup wire. (Additional wire available for purchase...see part number FGD-0010 or FGD-0010B). *It is essential that any water sensor used with the Sensaphone or a WisDom Wireless Universal Transmitter be self-powered.

The Humidistat Humidity Switch can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic, a nylon sensing element provides long life and accurate humidity control.

The Zone Water Detector senses the presence of water via the attached WaterRope. The Zone Water Detector can be used with all models of Sensaphone. The sensor is a normally closed device. It operates on two (2) AA batteries (installed). The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope.

10 foot length of WaterRope for the FGD-0056 Zone Water Detector. Up to ten (10) lengths of 10 foot rope (total length 100 feet) can be cascaded from a single Zone Water Detector. Dimensions: 10 feet long Compatible with the FGD-0056 Zone Water Detector.

The FGD-0222 float switch is a plastic side mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation.

For use with all Sensaphone models* except 400 and 800. A space mount, low profile humidity transducer. Transmits actual humidity levels to the Sensaphone for programmable high and low alarm limits. The device can be used with any Sensaphone that supports 4-20mA inputs.

Exclusively for use with the FGD-0052 Humidity Transmitter, the FGD-0065 Carbon Monoxide Sensor, the FGD-0066 Air Quality Sensor, and the FGD-0068 Carbon Dioxide Sensor. It is only required when connecting the transmitter/sensors to the Sensaphone 2000. (Other compatible models supply their own 24V power.

Old Code: M-001-0076, New Code: PS110 A compact power outage monitoring device to protect against power outages. The Power-Out Alert easily plugs into any 110 VAC receptacle outlet for operation.Works with all Sensaphone products.  Output is Normally Open. Includes 15 ft. cable.  Note:  This unit has an activation delay of approximately 3.

The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0053).

The Sensaphone IMS-4310 Dual Relay Output Module allows you to control two devices from any IMS-4000 Host or Node. Each output may be controlled either manually or automatically. Each output has the option of providing either a dry relay contact or 12VDC power. Two switches located inside the device select the output type.

The IMS-4815 Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm such as defrost cycles, opening of doors and fans circulating air.

The IMS-4815 Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm such as defrost cycles, opening of doors and fans circulating air.

The Sensaphone IMS-4863 Airflow sensor is designed to monitor for the presence or absence of cool moving air. This is especially useful for monitoring air conditioning systems. The sensor can provide relative air flow as a percentage from 0 to 100. The sensor is compatible with both the Sensaphone IMS-1000 and Sensaphone IMS-4000 devices.

The IMS-4816 Temperature Sensor with External Probe is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor temperatures in areas where a traditional sensor won’t fit. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable.

Sensaphone IMS-4814 Ultra Low Temperature Sensor for Sensaphone IMS-4000 or Sensaphone IMS-1000 The IMS-4814 Ultra Low Temperature Sensor is designed to connect to the Sensaphone IMS-1000 or Sensaphone IMS-4000 Host or Sensaphone IMS-4000 Node and monitor temperatures in refrigerators or freezers.

Sensaphone IMS-4002 Expansion Node adds 8 additional environmental inputs, the ability to monitor an additional 64 IP addresses and additional power monitoring to the Sensaphone IMS-4000 Host. Up to 31 Nodes may connect to any host.

Sensaphone IMS-4003 International Node for Sensaphone IMS-4000 with an external universal power supply.